Good building design and construction handbook page 4 forewords yiping zhou director special unit for south-south cooperation, undp good building design and construction the experience of the philippines is the second in a series of publications dealing with the same topic.The first one was based from the experience in.
Iai scon-cgb first step manual.Download first step manual of iai scon-cgb controller, switch for free or view it online on all-guides.Com.This version of iai scon-cgb manual compatible with such list of devices, as scon-cgb, scon-cb, scon-cal, scon-ca, scon-c.
View online operation instructions manual for girbau eh020 washer or simply click download button to examine the girbau eh020 guidelines offline on your desktop or laptop computer.
La premire phase du programme a t entame il y a plus dun an une seconde phase a t approuve qui.Prvoit lamnagement dune salle de classe et la dsignation dun matre priv pour 12 enfants en ge dcole primaire, issus de familles trs dfavorises.
Three-phase ac power supply mccb mc on off mc t 2 mc 3 5m 16.4feet or less mc rl1 motor im inverter brake unit mt-bu5 resistor unit mt-br5 sl2 tl3 u v p n p pr p pr p pr p th1 th2 pr cn8 w three-phase ac power supply mccb th1 th2 mc on off mc cr1 cr2 cr1 cr2 t 1 5m16.4feet or less 2.
Kp78 - ii 3000plus with 5d78 instruction manual v.Sb.3 please note this manual treats the setup and use of a 3000plus meter in which a daytronic model 5d78 ac strain gage conditioner module.
To operate all huck hydraulic installation equipment exclud-ing huck-spin tools.Model 940 operates on 115 volt ac, 50-60 hz, one-phase electrical power.The power cord is a 103 sjto cord with a nema l5-30 plug.The motor on the powerig is rated at 115v, 5060hertz, 25a.An electrical enclosure contains a motor contactor, trans-.
A 2.2 mfd 250 vdc capacitor with spade lug terminals, ready for installation.A tachogenerator must be installed and driven by the dc motor.The kit is intended to be used with the model 27-206 tachogenerator which has a 15vdc per 1000 rpm output, however, any dc tacho giving an output of 20 to 80vdc at rated motor speed can be used.
Mountin nstruction n olerance a e oun he mounting instructions and tolerances can be found in the torque nstallatio anual.Anual n 3 a le a e torque installation manual.Motortype.Max voltage ph-ph 3-phase synchronous frameless torque.230v ac rms 300v dc 420v ac rms 600v dc.Rms 0.297 0.595 1.07 2.86 motor constant coils 25c k.
4.Remove motor cable.1.3.1 side-by-side installation the frequency converter can be mounted side-by-side for ip20 rating units and requires 100 mm clearance above and below for cooling.Refer to chapter 1.7 specifications for details on environmental ratings of the frequency converter.Quick guide vlt micro drive fc 51.
Includes ic200udr164 24vdc inrelay out, ac power supply, ic200usb001 rs-232 option board with 2 0 -10vdc analog in with versamax datapanel dp45 with proficy logic developer programming soft ic200tbx420 tool box, micro 20, stepper motor, powercube amplifier and software.
Motor rated speed rpm motor rated frequency hz motor rated full load current amps motor rated horsepower remove the terminal cover to expose the motor and power terminals.A.Connect ac power to l1, l2, and l3 terminals.B.Connect ac motor leads to t1 u,t2 v, and t3 w.
2 installation 2.1 before you start this chapter contains some important details you should read and check before switch on the mc for the first time.I mains power voltage check the correct ac mains power voltage setting 240 vac at 5060 hz is the default value.
It consists of 4 parts pv modules, pv pump inverter, 3 phase ac pump and water storage device.Solar pumping inverter converts dc power produced by pv module into ac power required by the pump motor.A microprocessor inside continuously monitor available energy levels and adjust pump speed, matching energy required to energy available.
2.General descriptions on the operation of the vacuum type remote racking device 3.Instructions for installation 4.Illustrations, photographs, and description of the equipment described in ch 1 general information, a.Scope.The illustrations in this document are provided as general information to aid in showing component locations only.
The challenge machinery company provides owners manuals on its products solely as a courtesy to its customers.See the information below before using this manual.These manuals are for reference only.These manuals include products which are non-current, unsupported or no longer produced by the challenge machinery company, and are.
Operate all huck hydraulic installation equipment excluding huck-spin tools.Model 940 operates on 115 volt ac, 50-60 hz, one-phase electrical power.The power cordis a 103 sjto cord with a nema l5-30 plug.The motor on the powerig is rated at 115v, 5060hertz, 25a.An electrical enclosurecontains a motor contactor, trans-.
Shown in fig 2 single phase use l1 and l2 only.Con-nect the ground lead to the power panel as shown.Replace the front cover.On three phase machines, check to see that the motor turns in the proper direction.Briefly turn the machine on and off then look at the belt.If it turns in the oppo-site direction of the arrow on top of the motor.
Instruction manual 940hs 940-220hs.Single phase, ac.Motor valve assembly 1 2 124467 electrical enclosure assembly 1 3 107316 dipstick 1 4 111351 pilot valve 1 5 506360 strain relief 2 6 124473 manifold assembly 1 7 124475 control panel assembly 1 8 124484 base panel 1 9 124735 wiring assembly 1 10 500063 socket hd cap scr 10-24x34.
2.General descriptions of the operation and maintenance of the medium voltage controller 3.Instructions for installation and placing the medium voltage controller into service 4.Instructions for part replacement 5.Information for ordering renewal parts 6.Procedure for critical adjustments 7.Illustrations, photographs, and description.
Harmonic reduction method for a single-phase dcac converter without an output filter.Based on the injection of mirror harmonics during co nstruction.Single phase voltage source.
C us made in the usa by goodman manufacturing company, l.P.Io-286b 2550 north loop west, suite 400 - houston, texas 77092 606 www.Goodmanmfg.Com or www.Amana-hac.Com.